View HMF6M32M6VA_4528155.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HANBit
HMF6M32M6VA
FLASH-ROM MODULE 24MByte (6M x 32-Bit) ,72pin-SIMM, 3.0V Part No. HMF6M32M6VA GENERAL DESCRIPTION
The HMF6M32M6VA is a high-speed flash read only memory (FROM) module containing 12,582,912 words organized in a x32bit configuration. The module consists of six 2M x 16 FROM mounted on a 72-pin, both-sided, FR4-printed circuit board. Commands are written to the command register using standard microprocessor write timings. Register contents serve as input to an internal state-machine, which controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from other flash or EPROM devices. Output enable (/OE) and write enable (/WE) can set the memory input and output. When FROM module is disable condition the module is becoming power standby mode, system designer can get low-power design. All module components may be powered from a single +3.0V DC power supply.
FEATURES
w Access time : 90, 120ns w High-density 24MByte design w High-reliability, low-power design w Single + 3V 0.3V power supply w Easy memory expansion w Hardware reset pin(RESET#) w FR4-PCB design w Low profile 72-pin SIMM w Minimum 1,000,000 write/erase cycle w Flexible sector architecture w Embedded algorithms w Erase suspend / Erase resume PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 - 90 -120 20 21 22 23 24 M Vss
PIN ASSIGNMENT
SYMBOL /RESET DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 Vcc DQ7 /CE_1L /CE_2L DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 NC /CE_3H DQ16 PIN 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 SYMBOL DQ17 DQ18 DQ19 DQ20 DQ21 Vcc DQ22 DQ23 /CE_1H /CE_2H DQ24 DQ25 DQ26 DQ27 Vss DQ28 DQ29 DQ30 DQ31 NC NC /CE_3L A19 /OE PIN 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 SYMBOL /WE A18 A17 A16 A15 A14 A13 A12 A11 A10 Vcc A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 A20 NC Vss
OPTIONS
w Timing 90ns access 120ns access
MARKING
w Packages 72-pin SIMM
72-PIN SIMM TOP VIEW
URL:www.hbe.co.kr REV.02(August,2002)
1
HANBit Electronics Co., Ltd.
HANBit
FUNCTIONAL BLOCK DIAGRAM
HMF6M32M6VA
DQ0 - DQ31 A0 - A20 /WE /CE_1L
32 21 A0-20 /WE /OE /CE /Reset /Reset DQ 0-15
A0-20 DQ16-31 /WE /OE
DQ16-31
U1
U3
/CE /CE_1H
A0-20 DQ 0-15 /WE /CE_2L /WE /OE /CE /Reset
A0-20 DQ 16-31 /WE /OE DQ16-31
U2
U4
/CE /CE_2H
/Reset
A0-20 /WE /OE /CE_3L /Reset /WE /OE /CE DQ0-15
A0-20
DQ16-31
DQ 16-31
U5
/WE /OE
U6
/CE
/CE_3H
/Reset
/Reset /CE_3L
Option resister
URL:www.hbe.co.kr REV.02(August,2002)
2
HANBit Electronics Co., Ltd.
HANBit
ABSOLUTE MAXIMUM RATINGS
PARAMETER Voltage on Vcc Supply Relative to Vss A9, /OE, /RESET, /WP_ACC Relative to Vss Voltage on All other Pins Relative to Vss Power Dissipation Storage Temperature Operating Temperature ( Industrial ) SYMBOL VCC VIN,OUT VIN,OUT PD TSTG TA
HMF6M32M6VA
RATING -0.5V to +4.0V -0.5V to +12.5V -0.5V to +4.0V 6W -65oC to +150oC -40oC to +85oC
Operating Temperature ( Extended ) -55oC to +125oC w Stresses greater than those listed under " Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operating section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS
PARAMETER Supply Voltage Ground Input High Voltage Input Low Voltage SYMBOL VCC VSS VIH VIL MIN 2.7V 0 2.0 -0.5 TYP. 3.0V 0 MAX 3.6V 0 Vcc+0.3V 0.8V
DC CHARACTERISTICS (CMOS Compatible)
PARAMET DESCRIPTION ER ILI ILIT ILO ICC1 (Note1) Vcc Active Write Current ICC2 (Note 2 and 4) ICC3 ICC4 During Reset Automatic Sleep ICC5 Mode(Note3) VIL VIH VID Input Low Voltage Input High Voltage Voltage for Autoselect and Vcc=3.0V 10% VIL=Vss0.3V -0.5 0.7xVcc 11.5 0.8 Vcc+0.3 12.5 V V V VIH=Vcc0.3V; 1.2 30 uA Vcc Standby Current Vcc Standby Current Vcc=Vcc max ; /Reset=Vss0.3V 1.2 30 uA Vcc=Vcc max ; /CE,/Reset=Vcc0.3V 1.2 30 uA /CE=VIL, /OE=VIH 90 180 mA Word Mode 1MHZ 12 24 Input Load Current A9 Input Load Current Output Leakage Current Vcc Active Read Current VIN=Vss to Vcc, Vcc=Vcc max Vcc= Vcc max ; A9=12.5V VOUT= Vss to Vcc, Vcc= Vcc max /CE=VIL, /OE=VIH 5MHZ 60 3.0 35 1.0 96 mA uA uA uA TEST CONDITIONS MIN TYP. MAX UNIT
URL:www.hbe.co.kr REV.02(August,2002)
3
HANBit Electronics Co., Ltd.
HANBit
Temporary Unprotect VOL VOH1 Output High Voltage VOH2 VLKO Note : 1. 2. 3. The Icc current listed is typically less 2mA/MHz, with /OE at VIH. Icc active while Embedded Erase or Embedded Program is progress. Low Vcc Lock-Out Voltage IOH=-100uA, Vcc= Vcc min Vcc-0.4 2.3 Output Low Voltage IOL=4.0mA, Vcc=Vcc min IOH=-2.0mA, Vcc=Vcc min 0.85xVcc
HMF6M32M6VA
0.45
V V V
2.5
V
Automatic sleep mode enables the low power mode when addresses remain stable for tACC+30ns. Typical sleep mode current is 200nA.
4.
Not 100% tested.
LATCHUP CHARACTERISTICS
DESCRIPTION Input Voltage with respect to Vss on all pins except I/O Pins -1.0V (Including A9,/OE, and /Reset) Input Voltage with respect to Vss on all I/O Pins Vcc Current Includes all pins except Vcc. Test conditions: Vcc=3.0V, one pin at a time. -1.0V -100mA Vcc+1.0V +100mA 12.5V MIN MAX
DATA RETENTION
PARAMETER Minimum Pattern Data Retention Time TEST CONDITIONS 150 C 125 C
O O
MIN 10 20
UNIT Years Years
ERASE AND PROGRAMMING PERFORMANCE
TYP PARAMETER (NOTE1) Sector Erase Time Chip Erase Time Word Programming Time Chip Programming Time (Word Mode) (Note3) Notes : 1. Typical program and erase times assume the following conditions: 25 C, 3.0V Vcc, 1,000,000 cycles. Additionally programming typical assume checkerboard pattern. 2. Under worst case conditions of 90 C, Vcc=2.7V, 1,000,000 cycles. 3. The typical chip programming time is considerably less than the maximum chip programming time listed, since
URL:www.hbe.co.kr REV.02(August,2002)
O O
MAX (NOTE2) 1.6 112 11 24 360 72 15
UNIT sec sec us Excludes sec (Note5)
COMMENTS Excludes 00h programming prior to erasure (Note4) system level overhead
4
HANBit Electronics Co., Ltd.
HANBit
most bytes program faster than the maximum program times listed
HMF6M32M6VA
4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the two-or four-bus-cycle sequence for the program command. See table 9 for further information on command definitions. 6. The device has a minimum erase and program cycle endurance of 1,000,000 cycles.
SOP/TSOP PIN CAPACITANCE
PARAMETER SYMBOL CIN COUT CIN2 Notes : 1. Sampled, not 100% tested 2.Test conditions TA = 25 C, f=1.0 MHz.
o
PARAMETER TEST SETUP DESCRIPTION Input Capacitance Output Capacitance Control Pin Capacitance VIN = 0 VOUT = 0 VIN = 0 36 51 45 45 72 54 pF pF pF TYP. MAX UNIT
TEST SPECIFICATIONS
TEST CONDITION Output load Output load capacitance, 30 CL (Including jig capacitance) Input rise and fall times Input pulse levels Input timing measurement reference levels Output timing measurement reference levels 5 0.0 - 3.0 1.5 1.5 ns V V V 100 pF 80R -90/ -120 1TTL gate UNIT
3.3V
2.7k Device Under Test CL IN3064 or Equivalent
6.2k
Diodes = IN3064 or Equivalent
AC
URL:www.hbe.co.kr REV.02(August,2002)
5
HANBit Electronics Co., Ltd.
HANBit
CHARACTERISTICS u Erase / Program Operations
PARAMETER SYMBOLS DESCRIPTION JEDEC tAVAV tAVWL tWLAX tDVWH tWHDX Standard tWC tAS tAH tDS tDH tOEPH tGHWL tELWL tWHEH tWLWH tWHWL tWHWH1 tWHWH2 tGHWL Low) tCS tCH tWP tWPH tWHWH1 tWHWH2 tVCS tRB tBUSY Note: 1. Not 100% tested. 2. See the "Erase and Programming Performance" section for more Information /CE Setup Time /CE Hold Time Write Pulse Width Write Pulse Width High Programming Operation (Note2) Sector Erase Operation (Note2) Vcc Setup Time (Note1) Recovery Time from RY//BY Program/ Erase Valid to RY//BY Delay Word Min Min Min Min Typ Typ Min Min Min Write Cycle Time (Note1) Address Setup Time Address Hold Time Data Setup Time Data Hold Time Output Enable High durning toggle bit polling Read Recovery Time Before Write(/OE High to /WE Min Min Min Min Min Min Min
HMF6M32M6VA
-90 90 0 45 45 0 20 0 0 0 35 30 11 1.6 50 0 90
-120 120
UNIT ns ns
50 50
ns ns ns ns ns ns ns
50
ns ns us sec us ns ns
u Alternate /CE Controlled Erase/ Program Operations
PARAMETER SYMBOLS DESCRIPTION JEDEC tAVAV tAVEL tELAX tDVEH tEHDX Standard tWC tAS tAH tDS tDH tOES tGHEL tWLEL tGHEL Low) tWS /WE Setup Time Min 0 ns Write Cycle Time (Note1) Address Setup Time Address Hold Time Data Setup Time Data Hold Time Output Enable Setup Time Read Recovery Time Before Write(/OE High to /WE Min 0 ns Min Min Min Min Min Min 45 45 0 20 90 0 50 50 120 ns ns ns ns ns ns -90 -120 UNIT
URL:www.hbe.co.kr REV.02(August,2002)
6
HANBit Electronics Co., Ltd.
HANBit
tEHWH tELEH tEHEL tWHWH1 tWHWH2 Note: 1. Not 100% tested. 2. See the "Erase and Programming Performance" section for more Information. tWH tCP tCPH tWHWH1 tWHWH2 /WE Hold Time /CE Pulse Width /CE Pulse Width High Programming Operation (Note2) Sector Erase Operation (Note2) Word Min Min Min Typ Typ
HMF6M32M6VA
0 35 30 11 1.6 50 ns ns ns us sec
URL:www.hbe.co.kr REV.02(August,2002)
7
HANBit Electronics Co., Ltd.
HANBit
u READ OPERATIONS TIMING
HMF6M32M6VA
u RESET TIMING
URL:www.hbe.co.kr REV.02(August,2002)
8
HANBit Electronics Co., Ltd.
HANBit
u PROGRAM OPERATIONS TIMING
HMF6M32M6VA
u CHIP/SECTOR ERASE OPERATION TIMINGS
URL:www.hbe.co.kr REV.02(August,2002)
9
HANBit Electronics Co., Ltd.
HANBit
u DATA# POLLING TIMES(DURING EMBEDDED ALGORITHMS)
HMF6M32M6VA
u TOGGLE# BIT TIMINGS (DURING EMBEDDED ALGORITHMS)
URL:www.hbe.co.kr Ltd. REV.02(August,2002)
10
HANBit Electronics Co.,
HANBit
HMF6M32M6VA
u SECTOR PROTECT UNPROTECT TIMEING DIAGRAM
u ALTERNATE CE# CONTROLLED WRITE OPERATING TIMINGS
URL:www.hbe.co.kr Ltd. REV.02(August,2002)
11
HANBit Electronics Co.,
HANBit
PACKAGE DIMENSIONS
HMF6M32M6VA
0.25 mm MAX
2.54 mm MIN
1.27 mm
Gold: 1.040.10 mm Solder: 0.9140.10 mm
1.270.08 mm
(Solder & Gold Plating)
ORDERING INFORMATION
Part Number
Density
Org.
Package
Component Number 6EA 6EA
Vcc
Speed
HMF6M32M6VA-90 HMF6M32M6VA-120
24MByte 24MByte
6MX 32bit 6MX 32bit
72 Pin-SIMM 72 Pin-SIMM
3.0V 3.0V
90ns 120ns
URL:www.hbe.co.kr Ltd. REV.02(August,2002)
12
HANBit Electronics Co.,
HANBit
HMF6M32M6VA
URL:www.hbe.co.kr Ltd. REV.02(August,2002)
13
HANBit Electronics Co.,

▲Up To Search▲

Price & Availability of HMF6M32M6VA

	To Download HMF6M32M6VA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .